Range Report
Finally got the chance to take the Beretta Neos .22 out to the range this weekend. Mounted a Sig red-dot scope on it that I bought from a friend. I put 450 rounds through it(Remington Viper's, Remington Thunderbolts, CCI Blazer's, CCI Velociter's, CCI Stinger's, and Federal blue box. Was really happy with the cycling and had 0 malfuctions, even when I loaded all 6 mags and rapid-fired the 60 rounds. Was very happy with that. I can't even say the same about my Ruger 22/45. Was also pretty happy with the trigger pull. I was a little disappointed with accuracy, not quite as good as my Ruger. It is definitely acceptable, but I am hoping it gets a little better the more I get it broke in and find the ammo it likes best. In the end I am very happy with this little pistol and it should serve it's intended purpose very well(a good little squirrel/plinking gun).
Jon
Jon
0
-
I took the CZ, newly aquired Taurus, and the newly aquired Marlin to the range today. I had my father-in-law tag along as a spotter.
Went to the pistol side first. The 40caliber CZ never ceases to impress me. A total pleasure to shoot. You can shoot it all day long with hot reloads and not feel it. Groups real nice off a rest. 2" @ 10yds, I'm sure with more practice I could dial it in better. I have made the conclusion that Alliant Bullseye powder is way to dirty. I put 100rds out today and it looked as though I shot 500. I have always thought that CZ's ergonomics are wonderful, but after looking at a Ruger P94 the other day with it's Hogue grips, I'd have to put the CZ second. The balance of the CZ makes for very quick follow-up shots, very easy to keep on target. I have to comment on the ease of cleaning in the CZ, hold the slide back and pop out the take-down pin, pull the slide off and your in buisness. Over 1500rds though it and not a FTF or FTE, with no misfires. Firing pin hits dead-center every time.
I'm very pleased with the Taurus Millenium Pro 9mm. I just picked it up less than a week ago. Also delightful to shoot. Not as accurate as the CZ, but much more accurate than the Keltec P3AT that this is replacing as a carry gun. I picked a box of CCI Blazer 115gr FMJ and 3 boxes of Remington 115gr MC. All functioned flawlessly, I wasn't overly impressed with the CCI's aluminum case, especially since it is a factor in producing cheaper ammo. However, the Remington green box at $6.50/box is over a dollar cheaper than the CCI. I thought the green box was also cleaner. Gun felt real nice in my hand. My father-in-law is over 350lbs and has big meaty hands, he also commented on the feel. The gun was balanced well and recoil was quite manageable, makeing in quick follow up shots. I have noticed that empty cases are not tossed the 20ft distance that the CZ puts em out. Instead they are tossed almost straight up. The CCI Blazers only popped cases about 6" out of the gun. About 2 feet with the Remington's. A few landed on my head.
The biggest suprise of the day was the Marlin 917VR that I purchased about 2weeks ago. It's their "new" addition to their 17HMR lineup. Blue heavy barrel on synthetic with their T900 trigger system. I wasn't in the mood to drop a couple hundred dollars on a scope so I ordered a Barska Huntmaster Pro 3-12x50 illuminated reticle scope to top it with, just to get a feel for their quality. I was very impressed with their intial quality and workmanship, for $40 I was a little anxious to find out how it would be. It is a very solid and well-made scope. It's multi-coated optics make for a crystal clear sight picture and it sports 12 brightness settings for the illuminated reticle. For the money, I really don't think you can beat this scope.
I took the scope and rifle in grabbed a set of Burris rings and had the scope mounted and bore-sighted. A real beauty with the scope mounted. After we finished with the pistols and cleaned em up, we drove down to the 100yds rifle range. Set up our rifle rest, targets, and rifle and got to work. We brought along Winchester Supreme, Federal, and CCI ammunition. The Winchester's sported polymer tipped V-Max bullets and the others had Speer TNT bullets, all in 17gr. The first 5rds scored in the 10ring at 4 o'clock. Immediately I could tell I really liked this gun. Just enough oomph to let you know that you were shooting something. A high-pitched "crack" told you this was no 22. From checking out the first set of rounds, I was very impressed with the consistancy of the groups and I knew this was a sweet little rifle. A few adjustments brought them to about the 3 ring at 9 o'clock, little too much I guess. A couple adjustments and 5rds later, we were cutting bullseyes.
This is the best group we had. The day was beautiful, ~80degrees, sun at our backs, just a few clouds in the sky and a soft 5mph breeze at all times. I shot this group around noon today, 5rds covered by a nickel. I haven't measured it yet. Needless to say, I am very impressed.
5 rounds at 100yds.
We then took it down to the 225yd range and set up some prarie dog shoot-n-c targets. I don't have a spotting scope so we decided to just throw some rounds out and see if we hit anything. We were a little low on our elevation as each round hit the bottom 1/4 of the P-dog. The rounds were still really close. If I had more time to run back and forth down the range we could have tried to get some tight groups, but I wasn't holding my breath. I think I'll stick the the 100yd range from here. At least for a while. We did meet a good-ol-boy who had built a Ruger M77 in 22-250, topped with a Baush and Lomb 6-24 scope and a super light trigger, you don't pull it, you just touch it. A real nice gun, he had us put some rounds through it, and I can tell you, I know what rifle I want next!
All in all it was a great day, beautiful, plenty of people out, shooting everything from 22s to 30-06's and more.0 -
Nice. Relate the tips and tricks you learned about the 91/30. I would be interested in learning them.
I have a 91/30 courtesy of GRD and his generosity.
I have not gotten past the sticky bolt syndrome that these are somewhat known for.
Does anyone know good methods of cleaning the chamber?
I have talked to guys about it and have a few methods but have not tried any.0 -
A good way to clean your chamber is to.
1. warm the chamber up with a hair dryer.
2. run a wet patch in the chamber. Any good solvent will do.
3. take cleaning rod end with a 410 brush and chuck the rod end in a drill.
4. run drill slow to mid speed for 15 to 20 seconds, clockwise. Do not go into the rifling just the chamber.
Then repeat a couple of times. And that should clean her up.0 -
Nice shootin! 0 -
Well alright! 0 -
Nice range report. 0 -
I think all of the Mosin Nagants are supposed to be fired with the bayonet attached. I found that info on a Mosin Nagant forum that no longer exists. Also all the different ammo types make the rifles shoot differently. I haven't had too much luck with accuracy with the type you have in the picture. Most of the surplus ammo is for the light machine gun, so is over powered for regular rifles. I just aquired some that is on the original stripper clips(and yes, it was in a sealed metal container), so I know that it was made for these rifles. I am going to give it a try, and will post my results for this stuff. Nice rifles, and will last many lifetimes as long as you remember to clean the bore immediatly after shooting. 0 -
haroldchrismeyer: The surplus ammo that I found is heavy (183gr). And yes the rifles were sighted in for 300 meters with bayonet. With out the bayonet it does change the harmonics of the barrel. If when you shoot your rifle with your new ammo, and still have accuracy issues email me and I will give you the sites where I got my info to help resolve the problems. 0
Please sign in to leave a comment.
Comments
68 comments