44.40 Reloading
I just picked up a Smith 544 (off GB, thanks very much) and will reload for it. I plan on keeping things on the mild side, mostly cast lead stuff. Am I correct that Smith uses a .429 diameter barrel? Are 44.40 dies set to the same .429 for case neck sizing or are they .427 - and if .427 does it make any difference?
Any other tips on reloading the 44.40 are appreciated. I hear it's a bit of a challenge to reload, then again I hear it's a piece of cake. Can't be any more of a challenge than the bottle necked stuff like 30 Luger or Sig, or thin necks like 22 Hornet, 218 Bee that I already do. I hope.
Any other tips on reloading the 44.40 are appreciated. I hear it's a bit of a challenge to reload, then again I hear it's a piece of cake. Can't be any more of a challenge than the bottle necked stuff like 30 Luger or Sig, or thin necks like 22 Hornet, 218 Bee that I already do. I hope.
0
-
I've loaded everything from ,427 to .429" with no particular trouble.
Just be careful not to crush the thin case mouth against the die entry and be sure brass is clean and lightly lubed so as to not scratch your steel sizing die.0 -
I only ever loaded one, a custom extra long barrel pistol (a Buntline wanna be). A Lyman 427 something mold lubed in a .429 sizing die. No issues that I recall. 0 -
quote:Originally posted by Hawk Carse
I've loaded everything from ,427 to .429" with no particular trouble.
Just be careful not to crush the thin case mouth against the die entry and be sure brass is clean and lightly lubed so as to not scratch your steel sizing die.
No worries, when that happens my thumb is usually in the way and gets sliced up.[;)]0 -
quote:Originally posted by Hawk Carse
I've loaded everything from ,427 to .429" with no particular trouble.
Just be careful not to crush the thin case mouth against the die entry and be sure brass is clean and lightly lubed so as to not scratch your steel sizing die.
^^ This is important ^^
I can think of a couple other things relative to the 44-40
If you really want accuracy slug your bore as they vary.
Also be wary of revolvers as the cylinder throat diameters vary greatly.
I strongly recommend Starline brass as it is much stronger than domestic RP and WW. Can take heavy crimping required for tube fed lever-guns as well.0 -
It isn't just the bore diameter that can vary from gun to gun in .44-40s, but the chamber can also. Years ago I loaded up a few black powder loads for a Winchester 1873 using new brass (don't remember the brand). I had annealed the necks. Every one I tried split in the body of the case, not the necks. Checking the chamber I found it to be WAY oversize. Winchester quality control left a lot to be desired in many ways as did their record keeping. 0 -
My (relined) .44 WCF has a small chamber neck. I could load .429" bullets in WW brass, but only .428" in Starline, and only .427" in RP. My 3rd generation Colt is worse, it will not accept anything in RP cases. 0 -
^
Thanks all. My brass and dies showed up today and I was going to load up, but I think I'll wait until the gun shows up later this week. I'm using Starline brass.0 -
Forget everything you?ve been told about reloading .44 WCF cartridges. Take your time and pay attention and the cases are no more fragile than any other brass case. Also, early in my reloading I was told that despite everything I had been told it wasn?t necessary to lube the cases. I was leary but gave it a try and never lubed
another case and out of the thousands of rounds of cartridges I loaded I never had a stuck case.0 -
Sorry, doubled up reply 0
Please sign in to leave a comment.
Comments
10 comments