What do you guys use to...
square your reticles to your actions on your rifles? I have a crude reticle alignment tool, but it still leaves a lot to guess work. Most of those cheap bubble level tools are worthless. What do you bench rest guys use to align your reticles?
I asked this on the experts forum, there's no way that a collimator can do this, is there.?.? I've had two people tell that they can...but I don't understand how.?.?
Thanks!
I asked this on the experts forum, there's no way that a collimator can do this, is there.?.? I've had two people tell that they can...but I don't understand how.?.?
Thanks!
0
-
Well, if I gotta use a level than I use a $90 Starrett right angle jobbie (the "expensive" starrett's run about $900 for a 12" level).
Normally I back away from the eyepiece and make sure the vertical post is aligned with the barrel/bore center line. By eye I'm normally within 1/4 deg of true.0 -
quote:Originally posted by Tailgunner1954
Well, if I gotta use a level than I use a $90 Starrett right angle jobbie (the "expensive" starrett's run about $900 for a 12" level).
Normally I back away from the eyepiece and make sure the vertical post is aligned with the barrel/bore center line. By eye I'm normally within 1/4 deg of true.
Do you have a link to what you are talking about.?.? I'm usually pretty good by eye too, but I'd like a tool to rule out any errors on my end. Does that "right angle jobbie" just level the rifle, or does it level the scope as well??? Thanks!0 -
Eric
Starrett number 134
http://www.starrett.com/download/338_p439_444.pdf (look on page 5 of 6)
Perhaps Dongizmo would be able to locate one (his store probably carries them)
Clamp the rifle in a vise (padded jaws)
Level across the bolt ways (or at least determine the amount of error)
Level across the top of the bottom ring (if the bolt ways were off, the error here should be the same)
Level across the top of the elevation turret (again, any error in the bolt ways should be reflected here).
I mention the error thing, because if you can't get the action perfectly leveled, maintaining the same amount of level error will still leave your retical square/plumb with the action0 -
I've found that snugging the rings can change the alignment even if they're tightened the same amount on each side. Most scoped rifles of mine have gotten more than one session of true plumblines. Don't know why that is... 0 -
quote:Originally posted by Tailgunner1954
Eric
Starrett number 134
http://www.starrett.com/download/338_p439_444.pdf (look on page 5 of 6)
Perhaps Dongizmo would be able to locate one (his store probably carries them)
Clamp the rifle in a vise (padded jaws)
Level across the bolt ways (or at least determine the amount of error)
Level across the top of the bottom ring (if the bolt ways were off, the error here should be the same)
Level across the top of the elevation turret (again, any error in the bolt ways should be reflected here).
I mention the error thing, because if you can't get the action perfectly leveled, maintaining the same amount of level error will still leave your retical square/plumb with the action
Thanks![8D]0 -
I simply line up ,the vert line agains a telegraph pole, & nip the scope evenly in the mounts..never fails 0 -
A telegraph pole or side of a building you know is true. Of course, you go back to having the action as perfectly vertical/perpendicular to that as you can. 0 -
quote:Originally posted by mond
I simply line up ,the vert line agains a telegraph pole, & nip the scope evenly in the mounts..never fails
Telegraph pole? What century are you living in? [;)][:D]0 -
"I've found that snugging the rings can change the alignment even if they're tightened the same amount on each side. ".......weaver rings are notorious for this, you have to put some 'english' on the scope before you snug the rings down. 0 -
I have 3/8" rope hanging on my wall vertically & horizontally and scope it to that. Just make sure the ropes are bubbled properly on the wall. 0 -
There was a post on this subject on another forum recently but I'll be darned if I can remember where. It involved using a mirror place about 10 feet away. Mounting the gun in a vise or even shouldering it you can aim at the mirror and see if the cross hairs split the muzzle right down the center. The gun doesn't have to be perfectly perpendicular for this to work. That's the way I remember it anyhow but I haven't tried it. I actually totally forgot about it until I read this post. I'm going to be mounting a new scope soon and I'll give this method a try. Dave 0 -
Wow! Makes sense and is easy to do. Will have to remember that. 0
Please sign in to leave a comment.
Comments
12 comments