lorcin L380

docsgunsmithing

February 11, 2003 06:51

I know what kind of pistol this is and am not misguided with the quality of the piece. I am interested in hearing from someone who has had some luck with shoot ball ammo through the Lorcin and the brand. I am planning on giving this pistol away and have cleaned it, I also polished the ramp to a high luster with out removing material. Comment please!


Emmett

0

• 

  docsgunsmithing

  February 11, 2003 06:51

  can anyone tell me how to disasemble
  a L380
  i am having problems
  i just cant figure it out
  thanks
  Docsgunsmithing@aol.com
  
  doc

  0
• 

  chunkstyle

  February 11, 2003 08:47

  Use a cutting torch.
  
  Iraqi: "Is it true that only 13% of American kids can find Iraq on a map?"
  American reporter: "Yes, but all 13% are Marines"
  
  "Women should always wear tight clothes, and men should carry powerful handguns." - Calvin

  0
• 

  lrarmsx

  February 11, 2003 10:47

  Insure the weapon is unloaded, both the magazine and the chamber. Remove the magazine, pull the trigger, take a ball point pen and push in at the center of the back of the slide (the spring stop/take down button), begin to pull the slide back, then slightly up, don't let the spring stop go flying, slowly let the spring stop come out into your hand, that should include the firing pin and the firing pin spring as well as the stop itself. Allow the slide to go forward over the top of the barrel. Clean as needed, re-assemble in reverse order. Again be careful to not let the firing pin assembly go springing across the room. Holding that in place, bring the slide back, down and in.

  0
• 

  docsgunsmithing

  February 12, 2003 06:45

  thanks for the help
  and for the comment oabout using a cutting torch
  well not this litte gun
  i have shot at least 10000
  rounds out of this gun flawless
  until the other day and the fireingpin broke
  now i have a new one in it and its ready to go
  some people find the worst in everything
  thanks again for the help
  Doc
  
  doc

  0
• 

  interstatepawnllc

  February 12, 2003 08:56

  Wow, and I was thinking ballpeen hammer![:p]
  
  "If your gonna be stupid, go find a democrat."

  0
• 

  queeksdraw

  February 12, 2003 12:59

  Doc. Just ignore the negitive Bozos they seem to get there kicks by sitting by their computer all day waiting to rag on someone they dont know and cant see. Letting all them little stars go to there head. As you can tell there are a lot of good folks on this site, don't fret over the other ones.
  
  You'v gota kill it to grill it

  0
• 

  kingjoey

  February 12, 2003 13:18

  Sounds like the way the Jennings is set up. Not that I own one or anything [;)]

  0
• 

  interstatepawnllc

  February 12, 2003 18:29

  Hey Queeky, get a personality or find a dictionary. Either one would do you a world of justice.[:0]
  
  "If your gonna be stupid, go find a democrat."

  0
• 

  searcher5

  February 12, 2003 18:43

  Doc- no sarcasm intended , but I can't get even a whole clip through a Lorcin that I inherited. I had pretty much relegated it to paper weight status. Did you really get 10,000 rounds through it? I don't mean to seem dubious, but I can't even get 3-4 through mine without a jam. Your experience would be appreciated, because up to this point, I considered it equal, if not beneath a Jennings, which I also have the dubious distinction of owning. ( Now holding down papers) . Thanks, Dan
  
  If it ain't broke-it ain't ours!!!

  0
• 

  docsgunsmithing

  February 13, 2003 08:09

  searcher5
  i have gotten at least 10000 round through
  it
  it has been a very good cheap gun
  i use rem oil on it and clean it at around 100 rounds
  with gunscrubber
  those 2 in combo have worked great for all my guns
  i swear by the combo
  if all your springs are good and u use theose 2 i havnt had ajam
  in any of my guns
  once and a while a double feed but no real jams
  thanks eveyone
  
  doc

  0

Please sign in to leave a comment.