Skip to main content
Help Center Community Shop

M96-Aftermarket Trigger? Scope Mount? Other?

dcloco
I know, I know...why sporter or bubba an M96? This one somebody already attempted to bubba...and my other M96 is an original, numbers matching, and a tack driver. I am near sighted, so I need the scope at the range or hunting.

Suggestions on scope mount? I am leaning towards a non drill application, but am open to other suggestions. Scout scope is ok, but have an excellent normal scope for the project already - prefer to use it. I do not want to use a scout type mount for a long eye relief scope - as I already purchased a scope for the project.

Triggers - who has used what?

THANKS in advance!
0

Comments

11 comments

Date Votes
  • dcloco
    This is what I have purchased thus far.

    From Brownells:
    240-001-950 MARK II SAFETY, M-95 18.95
    019-000-008 MBH1800 98 MAUSER CONV. BOLT HANDLE 15.49

    And a Timney trigger (no safety model).

    It was cheaper to go with the Timney trigger with no safety on the trigger and install a low profile aftermarket trigger.

    Looking for a scope mount. Suggestions?
    0
  • jonk
    B square makes a no drill scout type mount that replaces the rear sight leaf and is, in my experience, quite stable. I have one and while I don't do any better than with the open sights, that's because I have a cheap scope on it, using so-so handloads.... which is hte only problem, this mount needs a VERY long eye relief scope.

    "...hit your enemy in the belly, and kick him when he is down, and boil his prisoners in oil- if you take any- and torture his women and children. Then people will keep clear of you..." -Admiral of the Fleet Lord Fisher, speaking at the Hague Peace Conf
    0
  • dcloco
    Thanks for the info. I purchased a normal scope for this project - worse case scenario, I will or hire it done - drill and tap.

    We shall see - there must be something out there.
    0
  • dcloco
    Bumping to the top.
    0
  • MIKE WISKEY
    drill and tap for the scope mount, i haven't seen a good 'no drill' mount yet (b-squares are junk). redfield makes A good mount and you do not have to recontour the reciever.
    0
  • ern98
    Ditto what Mike says, if the scope mount isn't straight and solid then you can't expect repeatable reliablity from the rig. Drill and tap for either a one piece mount without recontouring the rear ring. Or D&T for a two piece with the recontour. I always go for the two piece for the weight savings. Those one piece mount seem to weigh 1/3 of what a light scope does. If you are at loss as to where to send it for this I might recomend ER Shaw's in Penn. As long a time, 6 months, isn't an issue they do a fine job for a real reasonable price, they can also cut and weld the bolt handle for you.
    0
  • roysha
    I totally agree with MIKE WISKEY. However, I would add that if you have the ability and skills to weld on, and finish a bolt handle, I suspect you should also have the ability to do your own D&T. Drill bit and taps are quite inexpensive. Since this seems to be a DIY project for you, a copy of one of the better gunsmithing type books would help a great deal. I have several but my favorite is "Gunsmithing" by Dunlap. Since my copy is from the early 60s I'm sure a lot of the information is out of date (still a lot of good stuff though)and I have not looked at a current copy, but I would suspect that it has been updated.
    0
  • ern98
    As far as a trigger goes Timiny makes a great aftermarket trigger for the M96. Brownells is the place to get one from.
    0
  • dcloco
    THANK YOU for the input.

    I am still "on the fence" on purchasing what I need to drill and tap for a scope mount. I have the ability, not sure if I want to spend the cash for the fixture (is it worth the money) or spend the money and have a gunsmith do the job.

    Great info on the 1 vs 2 piece scope mount.

    I purchased a Timney trigger from Midway - they were quite a bit cheaper than anybody else - 33.99 (without built in safety). There seems to be QUITE a range of pricing on Timney triggers - when comparing the same Timney trigger from company to company....from $75 to $33.99.

    Any thoughts on a side mount scope?

    The bolt handle is already partially bent - somebody already started. I have decided to cut the bolt and drill and tap with one of the aftermarket bolt handles.

    Of note, I did find somebody that offers bent bolts for $35 - that is a great deal. Has several different styles as well.

    Bent bolt handle link: http://www.mosinnagant.net/Boltman/Boltman.html
    0
  • mauser_central
    everyone that said drill it is right on. Ive saw and tried other methods the ati stock w/ scope mount ..no good..... the no drill mounts......no good.....

    in my opinion side mounts are awkward and not as accurate

    midway has the drill n tap fixture you need, comes with everything but the mounts. just follow the instructions and its ez as pie with the jig, now i'd suggest buy it drill your receiver then sell it on ebay when your done they go for as much or more than midway sells em for.[:)] hope this helps

    "When a strong man, fully armed, guards his own house, his possessions are safe
    ~ Jesus Christ [Luke 11:21.6]

    Mauser Central

    MidwayUSA, if your not signed up for the Eblast alerts you are missing some great deals !
    0
  • roysha
    You don't need a drill and tap fixture. Level the bottom of the receiver. Position the scope base on the receiver and level it. Mark the holes. Drill and tap. All the Mausers I have ever D&Ted were butter soft so there should not be any problem with hardness like some Springfields. I realize this is a very simplified explanation but that is basicly how it's done. Drill and taps should not cost more than $15.00 or so and you can reuse them a couple of times. Around here most of the places are getting from$7.50 to $10.00 per hole plus a flat shop fee. I personally prefer the one piece base since I think they are stronger and have one less hole to drill. Weight difference is of no consequence as far as I'm concerned.
    0

Please sign in to leave a comment.

Recent Activity