Beretta Model 92
I just purchased a slightly used Model 92, 9mm. It is identical to the military version with the exeception the rear sight has two dots, rather the M9's one center line. My question how can I tell if the gun I own is the "modified version". I heard Beretta started having problems with the slide coming of the back of the gun during recoil, the fix was a simple one. But how can I tell if my gun has this feature?? By the way, it is a great shooter. Thanks in advance.
Alleno
Alleno
0
-
I having an unusual issue with my Model 92 FS lately. Each time I've taken it to the range for the last four trips, I've had one round out of about forty fired that has kicked back a lot of gas and powder residue in my face. Each time, just one. My loads are a little warm, using a Lee 7cc dipper of Blue Dot under a 124 gr. FMJ bullet. Been using it for years with no problems and even had a Ruger technician tell me it was OK a few years ago when talked to him about the P89 used to have. Any thoughts? Am I dealing with an ammo issue or a gun issue? Can't see where it would be the gun but never had a problem with this load in over 20 years either. 0 -
Prove it with next trip using factory loads. 0 -
My 92 does that...seems the excess oil pushes out of every opening and spits back at me[B)]
I like to keep my guns oiled.[:)]0 -
Just found the offending case. About a 1/4 inch blowout in front of the extractor groove. Case is a surpuls case with NATO and WCC markings. Maybe I've just reloaded it too many times. Will try some loads with new brass and some factory ammo. 0 -
You could also try backing off on your powder load a bit. There is no benefit to pushing the limit on a 9mm. It isn't going to make any difference on whatever it hits. Might as well use a load that is more reliable and less punishing on the gun. 0 -
I would suggest not using a dipper for powder measuring and use a powder thrower and scale instead. Its too easy to over charge when loading a small capacity case like the 9mm. Using load data from your book try loading a little below max loads, easier on the gun and cases. 0 -
In addition to what's already been said, the Beretta in particular has an aluminum frame that is known not to hold up well to diets of potent 9mm loads.
That's another good reason to keep the loads moderate.0 -
Check your dipper consistency with a digital scale. You'll be suprised how far off you can be, even when you're careful. With small cases and near max loadings, that tiny bit can be the difference between a blown case and a safe load. 0 -
quote:Originally posted by beantownshootah
In addition to what's already been said, the Beretta in particular has an aluminum frame that is known not to hold up well to diets of potent 9mm loads.
That's another good reason to keep the loads moderate.
I'll add that cracked locking lugs are also an issue with 92's and M9's subjected to these type of loads.0 -
9x19 factory loads are so cost effective...
Why bother with reloading for the 92fs?0 -
"Dipper" and "a little warm" do not work well together.
The Lee .7 dipper is rated for 8.1 gr Blue Dot.
The Alliant MAXIMUM is 7.9 gr Blue Dot and a 124 gr bullet.
A .2 gr overload is not much in the great scheme of things, but a well worn piece of brass can, DID, cause trouble.0 -
Thanks all,
Will likely trash cases earlier and reduce my load. The 92 is a relatively new acquisition. Got away with this load with my CZ 75 and P89 for many years but it's obviously time to back off a bit. FWIW, that Ruger technician I mentioned earlier told me European made guns are made for hotter loads so the Italian built 92 suprised me with this problem.0
Please sign in to leave a comment.
Comments
12 comments