Bad sight on Glock
I have a Glock model 17. I bought it 2 nd hand.
The rear sight is loose and tends to flip up. It is the white outline standard...I think.
If I order a new rear sight, how to remove and replace sight???
The rear sight is loose and tends to flip up. It is the white outline standard...I think.
If I order a new rear sight, how to remove and replace sight???
0
-
Youtube it. Funny how Youtube replaced Google [:D]. 0 -
quote:Originally posted by mrdropcloth
I have a Glock model 17. I bought it 2 nd hand.
The rear sight is loose and tends to flip up. It is the white outline standard...I think.
If I order a new rear sight, how to remove and replace sight???
Its pressure fit in a dovetail. You'll need a "sight pusher", or, with more difficulty, it can be drifted out/in. Any LGS will have a sight pusher.
As stated, there are videos on you tube that will demonstrate.0 -
What's a LGS? 0 -
LGS: Lazy Gun Smith?[:D] 0 -
quote:Originally posted by yoshmyster
Youtube it. Funny how Youtube replaced Google [:D].
They're part of the same entity. Google bought out YouTube and has owned it since 2006.
Anyway, to address the original question, IMO Glock "Perfection" doesn't extend to the OEM sights. These are plastic, and especially ones on early Glocks are known to have issues with loose fit and/or breakage.
Fortunately, replacement Glock sights are readily available and relatively cheap. Just find a set you like and go for it. If you want to try replacing with a plastic OEM type rear sight, you can buy these for as little as a few bucks.
Any gunsmith should be able to install this for you at a reasonable cost.
If you want to do it yourself, the old sight slides out in a dovetail groove left to right, new one slides in right to left. See here for complete installation instructions:
http://www.youtube.com/watch?v=ABAGA1eNx-k
While it is possible to adjust and install sights using a brass punch, hammer, and careful "tap-tap-tapping", this is imprecise, and zeroing a sight this way requires a little trial and error and can be frustrating.
Sight pusher makes installing, and especially zeroing new sights much easier. Good Glock specific ones cost about $100, but you can get a functional generic one that will work fine for under $40 (perhaps well under).
If you're "budget challenged" do-it-yourself sight pushers can be made from C-clamps for a few bucks, and while not elegant, can get the job done if you're careful. Again, you can Google, or YouTube search for this, and you'll see a variety of home-made ones out there.
Edit: I'd assume LGS is "local gunsmith". They shouldn't charge much for this service. IMO, sight pusher is a worthwhile too to have if you've got a lot of guns or like to tinker with them, again, best use of this is for fine adjustment of sight zero.0 -
quote:Originally posted by beantownshootah
...Glock "Perfection" doesn't extend to the OEM sights. These are plastic, and especially ones on early Glocks are known to have issues with loose fit and/or breakage.A lot of truth in that statement.
I've seen more sight separations during training - both front and rear - on Glocks than any other type. Those plastic to steel arrangements don't stand up well, especially when you start working on one handed reloads.0 -
quote:Originally posted by nunn
What's a LGS?
Your gun shop, David [;)]
L-ocal
G-un
S-hop0 -
quote:Originally posted by nunn
What's a LGS?
Local Gun Shop.
You must be new here? [:D]0 -
Not new here. Someone stated that "any LGS" would have a sight pusher. If mine is a LGS, this statement is incorrect, since I don't have a sight pusher. 0 -
Flipping up sounds like your rear sight may be the adjustable style.
Truglo sights with Tritium should go into that pistol.
TGH3 has green front and yellow rear illuminated dots.
They're the best day/night sights on any of my pistols.
I wouldn't spend any money fixing original sights.0
Please sign in to leave a comment.
Comments
10 comments